Spot Vignette Filter: Put the spotlight on elements within your design

Shining a spot light on something


Combined with other filters, Spot Vignette can add some very interesting effects, drawing attention to specific areas of a design. Similar to shining a spot light on something, this filter can also be used within selections to emphasise motifs. 



Instructions

  1. Open the Filter Browser, and add a new filter set using the small + icon located in the middle of the browser. This will create a new ‘untitled’ filter set for you. This will appear in the top section of the Filter Browser. If you already have filter sets created, clicking the + button will duplicate the selected filter set.
  2. Select Spot Vignette from the list of available filters in the lower section of the Filter Browser. 
  3. Double click on the name of the new filter set in the top section of the browser, and name it appropriately. 

  4. Edit the variables to achieve the result you need. 
    • Radius - enter a number between 1 and 1500, or use the slider to try different settings. The higher the number, the wider the spotlight.
    • Intensity - enter a number between 0 and 1.  the higher the value, the more intense the spotlight will be.

In the snapshot below, the original data is on the left, and the filtered data is on the right.

Delete


Using the Centre options

The origin of the effect applied by this filter will be the centre of the design, unless you specify a new origin using a pin or selection.

Around a pin

  1. Select the Pin Tool from the Tools Palette. 
  2. Click in the area of the design you want to apply this effect around. This will place a pin in that area.

  3. Edit the variables of the filter until you achieve the effects you need, and use one of the three options described in the next tab to apply the filter

In relation to a selection

  • Draw a selection around the area you wish to apply the filter, and press the Selection button under the filters variables. The new origin will be shown in brackets underneath, and the effect will now be centred within the selection.

Clearing the Centre options

  • Press the X at any time to clear the new origins. 

Delete


Applying the filter

There are several ways to apply a filter:

  • Click Apply – this will apply the filter to the active layer(s), and within a selection if there is one present in your file
  • Click Make Layer – this will make a new layer in your file containing the filtered effect, leaving the original layer untouched
  • Apply the filter using the Brush Tool – when you have finished building your filter set, simply close the Filter Browser. Then, open the Brushes Library, and select the filter you have just made from the drop down menu shown in the snapshot below. You can now paint with your filter.
Delete

Note: The default setting for the Brush Tool is ‘Brush”, located at the top of this drop down menu. To prevent you from becoming confused between the default setting and a filter setting, do not name any filters ‘Brush’. When you have finished painting with your filter, set the drop down menu back to the Brush setting, otherwise the Brush Tool may not behave as you would expect later on.

Delete

Applying the filter over a repeat join

For a full explanation on how to use filters, view the Filter Browser article.  Each individual filter is further explained in it's own article and can be searched on in the search bar above. 


Some of the filters do not work correctly across repeat joins when used in the normal way. Therefore it is important to follow this method to make sure the filter works correctly and does not affect the join. Your design must repeat correctly before you do this.

  1. Open the Selections Palette.
  2. Press Offset Repeat. If you are not already viewing multiple repeats of your design, AVA will automatically put your design into s 2x2 repeat when you press this.  A selection the size of a single repeat will appear in your file, offset to the first repeat, which is framed in blue in the snapshot below.

  3. Activate the layer / image you want to filter.
  4. Open the Filter Browser.
  5. Apply your the filter. The filter will work correctly in repeat, with no obvious repeat joins. In the image below, the vertical line is the repeat join. 


Delete

Note: This method does not work for all filters, including Clouds, Waves and Tile. If you need to fix a repeat join using the Clouds Filter, we recommend using a Palette to create a brush which uses a Clouds Pattern, and using this repair the repeat joins. 



Delete


Was this article helpful?


Knowledge Base Software powered by Helpjuice