FAQ: Colour separations


Which separation method should I use?

Deciding with separation method to use can be a daunting task.  However, it really depends on the type of design you are trying to separate. The chart below will guide you towards the separation methods to choose.



Flat colour

Tonal but no overprinting colours

Tonal with lots of overprinting colours

Photographic
1622220063092-Which separation_a.jpg
1622218269087-Which separation_b.jpg
1622218299655-Which separation_d.jpg







The design is flat colour, or the resulting separation should be completely flat, and there are no overprinting areas

The design is tonal, however there are no overprinting areas at all



The design is made up from overprinting colours, and this must be reflecting on the separation


The design is photographic and needs to retain this quality when separated





Suggested separation methods




Auto with Create

Automatic




Spot












The methods above are simply a suggested starting point.  It is common for separation artists to use a combination of separation methods in order to achieve the best results.  



Delete

Are there any tips for quickly cleaning up separations?

Designed to work on flat, butt-fitting layers, the Despeckle Filter removes stray pixels, or groups of pixels which are surrounded by another colour, and place them on other, more appropriate layers. It is most often used to clean up separations and remove areas of noise on separated layers.


Instructions

  1. Open the Filter Browser, and add a new filter set using the small + icon located in the middle of the browser. This will create a new ‘untitled’ filter set for you. This will appear in the top section of the Filter Browser. If you already have filter sets created, clicking the + button will duplicate the selected filter set.
  2. Select Despeckle from the list of available filters in the lower section of the Filter Browser
  3. Double click on the name of the new filter set in the top section of the browser, and name it appropriately
  4. Edit the variables to achieve the result you needIn the example below the filter is being used to reduce all tones

    • Speckle size -  the software looks at groups of pixels up to and including the set amount. For example, if you type 20 in the window, the software will look for groups of 20 pixels or less and will change them to the closest, or surrounding colour. Either enter the value needed or use the slider to preview and try out different amounts. The maximum speckle size you can use is 300.

    • Preserve Diagonals - switching off preserve diagonals makes the despeckle effect more coarse. With preserve diagonals switched on, line detail will remain the same and pixels on the edge of motifs will be kept in tact.

In the snapshot below, the original data is on the left, and the filtered data is on the right.

Delete


Applying the filter

There are several ways to apply a filter:

  • Click Apply - this will apply the filter to the active layer(s), and within a selection if there is one present in your file
  • Click Make Layer - this will make a new layer in your file containing the filtered effect, leaving the original layer untouched
  • Apply the filter using the Brush Tool - when you have finished building your filter set, simply close the Filter Browser. Then, open the Brushes Library, and select the filter you have just made from the drop down menu shown in the image below. You can now paint with your filter.
Delete

Note: The default setting for the Brush Tool is ‘Brush”, located at the top of this drop down menu. To prevent you from becoming confused between the default setting and a filter setting, do not name any filters ‘Brush’. When you have finished painting with your filter, set the drop down menu back to the Brush setting, otherwise the Brush Tool may not behave as you would expect later on.

Delete

Note: This filter does not work on images.

Delete


Applying the filter over a repeat join

Some of the filters do not work correctly across repeat joins when used in the normal way. However, the Despeckle Filter, does.  All you need to do is use the Repeat Window to put your design into a 2 x 2 repeat prior to applying the filter.

Delete



This function makes easy work of cleaning up dirty or noisy separations, particularly following colour separations done using Automatic or Auto with Create. It works by moving pixels from one or more specified layers to another. It is extremely useful when dirty areas in a design have not separated correctly and need to be cleaned up. 


How to use the Mover Tool

  1. Make all the layers to be cleaned up active and visible.
  2. If the window is not already open, go to Window Menu > Mover or click on its shortcut in the toolbar.
  3. Select one of the presets you have already created using the steps above.
  4. Draw over the area to be moved in the design with one of the painting tools and the information will change from the colours selected on the left (in the From column), to the colour selected on the right (in the To column).

Note: You can move pixels from more than one layer at once (within the same preset), but should only move pixels to one layer at a time.

The top section of the Mover Tool window explained

The top section of this window shows all the layers in your file. If any appear to be greyed out, it is because they are not active in the Layers Palette. In order to move pixels from or to a layer, the layer must be active. This section also includes the To and From columns. Specify which layers the pixels are moved from and to, by ticking the relevant boxes, thus creating a setup.

  • Clear - will remove the current setup from the selected preset, making it quick and easy to change that setup
  • The arrows - will swap the order of the selected setup

The bottom section of the Mover Tool window explained

This section is used to add and delete presets which are subsequently saved with the file when it is saved in our .ava4 format.  

Taking the time to build a library of presets will undoubtedly save you time during the actual clean up process of your separation.  To create presets, follow the steps below:

  1. Activate all layers in your design.
  2. Go to Window Menu > Mover to open the Mover Tool. 
  3. Click the small + button at the bottom of the window.  An untitled preset will be created.
  4. Choose the setup required by clicking on the relevant To and From columns in the top section of the window.
  5. Double click on the word Untitled and name your preset accordingly.
  6. Repeat this process until all setups are complete.

Note: Clicking and dragging your cursor over the presets will quickly show you all of your setups.

The Movie




Was this article helpful?


Knowledge Base Software powered by Helpjuice